Research Projects at Mechanical Engineering Department
20
Projects Completed
21
Projects Ongoing
Rs. 7043.41
Total Outlay (in Lakhs)
Completed Projects
Ongoing Projects
Completed Projects
| Sr No | Title | Sponsoring Agency | Outlay (in Lakhs) | Year of Sanction | Investigator |
|---|---|---|---|---|---|
| 1 | Analysis of complete laying circuit of 155 mm 45 cal Dhanush gun system to increase reliability and sustenance in gun operation and maintenance | Gun Carriage Factory, Jabalpur | 25 | Dr. V.R. Kalamkar | |
| 2 | Simulation of Pressure Casting of Viscous Slurry into Cylindrical Cavity | HEMRL | 10 | Dr. V.R. Kalamkar | |
| 3 | Smart Foundary 2020 | DST | 950 | Dr. A. M. Kuthe | |
| 4 | Development of a Vascular Anastomosis Device | DST | 23.39 | Dr. P. M. Padole | |
| 5 | Performance Analysis and Optimization of recoil mechanism of 7.62 mm assault rifle | Ministry of Defence | 24.0787 | Dr. V.R. Kalamkar | |
| 6 | Design, Analysis and Optimization of 15 mm Artillery Gun | Ministry of Defence | 24.756 | Dr. V.R. Kalamkar | |
| 7 | Biomechanical behaviour of Mandibular overdenture retained by one or two standard sized or mini implants: 3D Finite Element Analysis | International Medical University, Malaysia | 1.5 | Dr. Rashmi V. Uddanwadiker | |
| 8 | Application of rate, state, temperature and pore pressure friction (RSTPF) model for rock slope stability and failure hazard assessment | NRDMS-DST | 13.5 | Dr. A.K. Singh | |
| 9 | Development of Fluid - Structure Interaction (FSI) Solver for Cardiovascular Disease: An Aneurysm | DST-SERB | 26.19 | Dr. Trushar B. Gohil | |
| 10 | Development of Digital Dental Restoration | Department of Science and Technology | 41.5 | Dr. Rashmi V. Uddanwadiker | |
| 11 | Development of Ni based composite coatings using electroless plating method for high temperature tribological applications | DST (ECRA) | 35.54 | Dr. Ravikumar Dumpala | |
| 12 | Development of Robot programming by demonstration system for spray painting operation | DST | 25 | Dr. Shital S.Chiddarwar | |
| 13 | Fabrication of experimental setup of a solar air heater and study the effect of rib shapes on the thermal enhancement of a solar air heater | TEQIP-II | 1 | Dr. A.S.Dhoble | |
| 14 | Design and Fabrication of Humanoid Robot | COE & Department of Electronics Engineering,VNIT | 10 | Dr. Rashmi V. Uddanwadiker | |
| 15 | Purchase of Sound and Vibration Analyzer | TEQIP | 45 | Dr. A.B. Andhare | |
| 16 | Centre for Advanced Technology in Mech. Engg.- FIST Project | DST | 170 | Dr. P. M. Padole | |
| 17 | KVIC Technology Dissemination | KVIC | 25.66 | Dr. P. M. Padole | |
| 18 | Estimation of human muscle characteristics | Department of Science & Technology | 13.16 | Dr. Rashmi V. Uddanwadiker | |
| 19 | Development and testing of customized joint replacement implant using layered manufacturing | RGSTC | 50.6 | Dr. A. M. Kuthe | |
| 20 | Fatigue testing of Hip Prosthesis | DRDO | Dr. P. M. Padole |
Ongoing Projects
| Sr No | Title | Sponsoring Agency | Outlay (in Lakhs) | Year of Sanction | Investigator |
|---|---|---|---|---|---|
| 1 | Design of 1 kW Roof Top Vertical Axis Wind Turbine | SERB | 23.09 | 2023 | Dr. S. R. Roga |
| 2 | Design and Demonstration of Empty and Foam Filled Honeycomb Structures for Energy Absorption During Crash/Impact | ISRO | 17.9 | 2023 | Dr. G. Tiwari |
| 3 | Investigation of Design Modification of Switched Reluctance Motor to reduce vibration and noise in Electric Vehicle | SERB | 28.31 | 2023 | Dr. P. V. Kane |
| 4 | Design and Development of customised mobility aids using bamboo for disabled villagers | Gondwana University Gadchiroli | 1 | 2023 | Dr. A. M. Kuthe |
| 5 | Wooden toy pilot project | KVIC | 13.27 | 2022 | Dr. A. B. Andhare |
| 6 | High Skill Training Lab Pilot Project | KVIC | 18.02 | 2022 | Dr. A. B. Andhare |
| 7 | Analysing the curve of occlusion among Malaysian adults using intraoral scanning images | International Medical University, Malaysia | 0.562 | 2022 | Dr. R. V. Uddanwadiker |
| 8 | Development of control strategy for human arm motion imitation system for industrial robot programming | TEQIP-III | 2019 | Dr. Shital S.Chiddarwar | |
| 9 | Experimental investigations on weldability of CRNGO electrical steel through cold metal transfer (CRG/2018/001619) | DST-SERB | 34.27 | 2019 | Dr. N.K. Lautre |
| 10 | Metal Additive Manufacturing using Laser Cladding Process | DST-AMT | 66.82 | 2019 | Dr. T. V. K. Gupta |
| 11 | Biomedical Engineering and Technology centre Incubation | DST/RGSTC | 3939 | 2019 | Dr. A. M. Kuthe |
| 12 | Response of hemispherical sandwich shell structures subjected to projectile impact | SERB (DST) | 21.97 | 2017 | Dr. Gaurav Tiwari |
| 13 | Online Monitoring and Characterization of Distorsion in Multi Layer Laser Cladding Process | DST-ECR | 37.19 | 2017 | Dr. T. V. K. Gupta |
| 14 | SMART Foundry 2020 | CAD-CAM Centre, Mech. Engg., VNIT, Nagpur | 950.1516 | 2016 | Dr. K.M. Ashtankar |
| 15 | Experimental and numerical study of flow and heat transfer in cross flow heat exchanger | TEQIP-II | 1.51 | 2016 | Dr. A.S.Dhoble |
| 16 | SWAYATT- The Humanoid, Design, development and fabrication | COE, Combedded Systems | 10 | 2014 | Dr. Shital S.Chiddarwar |
| 17 | Mathematical Modeling of Hydraulically Operated Zero Velocity Valve | Flonix Valves Ltd., Pune | 2.5 | 2014 | Dr. A.S.Dhoble |
| 18 | Bio Medical Engineering and Technology Incubation Sub Centre (BETIC) | DST/RGSTC | 360 | 2014 | Dr. A. M. Kuthe |
| 19 | Project on capacity enhancement of pulverizer | TYCO India Pvt. Ltd. | 1 | Dr. M.S. Kotambkar | |
| 20 | Design and analysis of of weld joints of aerofoilin jet Blast Deflector | Anand Mine Tools Pvt. Ltd | Dr. A.S.Dhoble | ||
| 21 | Performance enhancement of grinding mill | Tyco (India) Pvt. Ltd. Nagpur | 1 | Dr. A.S.Dhoble |